nanonixos
Artifact Content
Not logged in

Artifact 3b11d7bf1ea31a579211febf61977d46a8af97e4:


After connecting the serial lines, I could see that pressing 'u' at boot with the usual uboot, I saw in the serial line:

NAND Secondary Program Loader

[U] pressed, goto USBBOOT mode
</verbabtim>

That means I can use xbboot or usbboot from the xburst tools. I have a jz-3.2
kernel built (vmlinuz.bin). I used this command line, stored in the kernel:
<verbatim>
CONFIG_CMDLINE="mem=32M console=ttyS0,9600n8  ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"

I load it this way:

# xbboot -u 0x80600000 vmlinuz.bin

Info - found XBurst boot device.
set_addr 80002000h
bulk_write successfully wrote 6088 bytes.
start1 80002000h
VR_GET_CPU_INFO JZ4740V1
set_addr 80600000h
bulk_write successfully wrote 2054683 bytes.
VR_FLUSH_CACHES
start2 80600000h

And at boot it says:

Ben NanoNote
GPIO, clocks, SDRAM, UART setup
now jump back to BOOT ROM...
ziess 80010000
Nkernel...
 the kernel...
[    0.000000] Linux version 3.2.0prova-86405-gc97b223 (viric@bergamota) (collect2: ld returned 1 exit status) #5 PREEMPT Wed Jan 11 20:03:56 CET 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0ad0024f (Ingenic JZRISC)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  mem=32M console=ttyS0,9600n8  ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Memory: 27616k/32768k available (3140k kernel code, 5152k reserved, 1060k data, 176k init, 0k highmem)
[    0.000000] NR_IRQS:190
[    0.000000] Console: colour dummy device 80x25
[    0.000000] Calibrating delay loop... 250.67 BogoMIPS (lpj=1253376)
[    0.090000] pid_max: default: 32768 minimum: 301
[    0.100000] Mount-cache hash table entries: 512
[    0.110000] Performance counters: No available PMU.
[    0.130000] NET: Registered protocol family 16
[    0.160000] JZ4740 GPIO initialized
[    0.180000] Qi Hardware JZ4740 QI LB60 setup
[    0.290000] bio: create slab <bio-0> at 0
[    0.310000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.320000] Switching to clocksource jz4740-timer
[    0.480000] NET: Registered protocol family 2
[    0.490000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.500000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.510000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.520000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.530000] TCP reno registered
[    0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.590000] JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 53
[    0.620000] io scheduler noop registered
[    0.620000] io scheduler deadline registered (default)
[    0.660000] Console: switching to colour frame buffer device 40x15
[    0.710000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.730000] serial8250.0: ttyS0 at MMIO 0x10030000 (irq = 17) is a 16550
(AND NOW, LOTS of ^@, so, zeroes)

Failures

After serial8250.0..., I see lots of zeroes

Loading the driver sets 57600n8 ttyS0 configuration. Then, you better use that console setting, instead of overriding it with things like console=ttyS0,9600n8.

UBI error: cannot initialize UBI, error -19

Thats in (drivers/mtd/ubi/build.c:536). -19 means, as -errno, for errno=ENODEV (No such device). It can be the next line to:

[    0.800000] jz4740-nand jz4740-nand.0: No NAND chips found

(I still don't know how to solve that. Someone (mth?) may have broken that)